FM-200 Fire Suppression System in Delhi NCR
An FM-200 fire suppression system protects a closed room by filling it with FM-200 gas (HFC-227ea) within about 10 seconds of detecting a fire. The gas puts the fire out without water, powder or mess, so your servers, panels and files survive. That is why it is the usual choice for server rooms, data centers and control rooms.
If your business stops when the server room stops, a fire in that room is not just a fire. It is lost orders, lost data and days of downtime. Sprinklers would put the fire out but drown the equipment along with it. FM-200 was made for exactly this problem: it stops the fire and leaves the room as it was. In Delhi NCR, where server rooms often sit in office floors with long summer power cuts and hard-working UPS batteries, it is one of the most common ways to protect them.
Where is the FM-200 Fire Suppression System used?
- Server rooms and data centers
- UPS and battery rooms
- Electrical and control rooms
- Telecom and network rooms
- Bank strong rooms and record rooms
- Hospital equipment rooms and labs
- Museums and archives
- Broadcast and studio rooms
How does the FM-200 Fire Suppression System work?
Two sets of smoke detectors watch the room. When one picks up smoke, an alarm goes off so someone can check. If the second set confirms it, the panel starts a short countdown, gives people time to walk out, and then opens the cylinder. FM-200 sits in the cylinder as a liquid under nitrogen pressure and turns into gas the moment it leaves the nozzles. It pulls heat out of the fire and breaks the chemical reaction that keeps it burning. For this to work, the room has to hold the gas for around 10 minutes, so open cable holes and gaps under doors matter more than most people think.
FM-200 Fire Suppression System at a glance
| Agent | FM-200 (HFC-227ea), a clean agent gas |
|---|---|
| Discharge time | About 10 seconds |
| Detection | Smoke and/or heat detectors with a control panel (cross-zoned) |
| Residue | None, electrically non-conductive |
| Occupied rooms | Suitable at the normal design level (people should still leave when the alarm sounds) |
| Room needs | Closed room; doors and openings sealed; dampers closed on discharge |
| Reference standards | NFPA 2001 (clean agents); NBC 2016 Part 4 (fire safety in buildings, India) |
FM-200 vs CO₂ vs other clean agents
| FM-200 | CO₂ | FK-5-1-12 / inert gas | |
|---|---|---|---|
| Safe for occupied rooms | Yes, at design level | No, only unoccupied areas | Yes, at design level |
| Residue | None | None | None |
| Discharge time | About 10 s | About 60 s or more | 10 s (FK-5-1-12) / about 60 to 120 s (inert gas) |
| Cylinder space | Small | Medium | Small (FK-5-1-12) / large (inert gas) |
| Best for | Server rooms, control rooms | DG rooms, transformer rooms, plant areas | Server rooms where low environmental impact is wanted |
One honest point: FM-200 has a high global warming potential. If your company has a green policy, ask us about FK-5-1-12 or an inert gas system instead. Both are covered on our clean agent page, and the server room guide compares all the options side by side.
How we work, step by step
- Site visit: We come and see the space ourselves, measure it, and look at what is likely to catch fire, how air moves, where the gaps are and where power comes from.
- Design: We pick the agent, size the system and send you a simple layout with quantities, so you know exactly what you are paying for.
- Supply: Cylinders, detectors, nozzles, pipes and the panel arrive as per the design you approved, nothing swapped quietly.
- Installation: Our team fits and wires everything. In live sites we plan the noisy work around your working hours.
- Testing: Before we call it done, we test detection, alarms, the release circuit and pressures, and show you the results.
- Handover: We walk your staff through the alarms, the abort and manual release, and what to do if the system ever goes off.
- AMC: After that, regular visits keep it ready. A system that is never checked is a system you are hoping works.
What we check on AMC visits
- Cylinder pressure and agent weight check
- Detector, panel and hooter tests
- Manual release, abort and hold switch checks
- Pipe, nozzle and bracket inspection
- Room integrity check for new openings
- Refilling after a discharge
- Service report after every visit
How often we visit is written into the AMC and depends on your room and how critical it is. Between visits, a quick look at the cylinder gauge once a month is a good habit.
You may also need
- Clean Agent Fire Suppression System
- Server Room Fire Suppression
- Total Room Flooding System
- Fire Alarm System Installation
- Guide: What is an FM-200 fire suppression system?
Want us to look at your server room? Call or WhatsApp +91 85870 53556 and tell us the room size, or send an enquiry. The site survey in Delhi NCR is free.
Design, testing & support
We design, install and look after FM-200 systems for server rooms, UPS rooms and control rooms across Delhi, Noida, Gurugram, Ghaziabad and Faridabad.
Site-specific design
Each system is sized for the room, panel, kitchen, building or vehicle it protects.
Tested at handover
Every installation is tested and commissioned before handover.
- Free site survey across Delhi NCR.
- System chosen for your actual fire risk.
- Protects equipment, people and operations.
- Reduces downtime and repair costs.
- Professional installation, testing and commissioning.
- Regular inspection, maintenance and AMC services.
Everything you need to know about FM-200 Fire Suppression System in Delhi NCR
It is a fixed system that floods a closed room with FM-200 gas within about 10 seconds of detecting a fire. The fire goes out, and there is no water or powder to clean, so equipment is not damaged.
At the concentration used for fire protection, FM-200 is considered safe for people, which is why it is used in rooms where staff work. Still, the system gives a warning before it releases, and everyone should walk out when they hear it.
No. It does not conduct electricity and leaves nothing behind. Most of the damage in a server room fire comes from smoke and heat, which the quick discharge limits.
It depends on the room and how ready the site is. Once the design is approved and material is on site, a small server room is usually a matter of days, not weeks. We give you a timeline after the survey.
AMC aam taur par ek saal ka hota hai. Isme visits, cylinder ka pressure aur weight check, detectors aur panel ki testing, aur har visit ki report aati hai. Kitni baar visit hogi, ye contract me likha hota hai.
Yes. After a discharge we refill the cylinder, check the detectors and panel, and test the whole system again before handing it back.