Sprinkler System Installation in Delhi NCR
A fire sprinkler system is a network of water pipes with sprinkler heads on the ceiling. Each head has a small glass bulb that breaks at a set temperature (often 68 °C) and sprays water only where the fire is. It controls or puts out the fire early, which is why it is the most common fixed fire protection in large buildings.
People often picture every sprinkler in a building going off at once, as in films. That is not how it works. Only the heads heated by the fire open. In most fires, one or two heads are enough to hold the fire until the fire service arrives. For warehouses, factories and malls across Delhi NCR, that early control is often the difference between a damaged corner and a lost building.
Where are fire sprinklers installed?
- Warehouses and logistics parks
- Factories and workshops
- Malls and showrooms
- Hotels and hospitals
- Office buildings
- Basements and car parks
- Residential high-rises
- Schools and institutions
How does a fire sprinkler system work?
The pipes are kept full of water under pressure from a fire pump and tank. When a fire heats a sprinkler head, its glass bulb breaks and that head starts spraying. The pressure drop starts the pump and rings an alarm. The other heads stay shut unless the fire reaches them too, so water damage stays limited. A typical pump room has a small jockey pump to hold pressure, a main electric pump and a diesel pump as standby for power cuts.
Sprinkler system at a glance
| Sprinkler head | Glass bulb (commonly 68 °C, red) |
|---|---|
| System types | Wet pipe, dry pipe, pre-action, deluge |
| Water supply | Fire water tank with jockey, electric and diesel pumps |
| Alarm | Flow switch, alarm valve and water gong |
| Pipes | MS / GI pipes sized by hydraulic calculation |
| Testing | Hydraulic pressure test before handover |
| Reference standards | IS 15105 (sprinkler systems); NFPA 13; NBC 2016 Part 4 |
Types of sprinkler system
| Wet pipe | Dry pipe | Pre-action | Deluge | |
|---|---|---|---|---|
| Water in pipes | Always | No (air) | No, until detection | No, heads are open |
| Best for | Most buildings | Cold or unheated areas | Server rooms, archives | Transformers, high hazard |
| Accidental discharge risk | Low | Low | Very low | Depends on detection |
| Response | Fastest | Slight delay | Needs detection first | All heads at once |
Sprinklers usually go hand in hand with a hydrant system and a fire alarm. Rooms full of electronics are better off with a clean agent system.
How we work, step by step
- Site visit: We come and see the space ourselves, measure it, and look at what is likely to catch fire, how air moves, where the gaps are and where power comes from.
- Design: We pick the agent, size the system and send you a simple layout with quantities, so you know exactly what you are paying for.
- Supply: Cylinders, detectors, nozzles, pipes and the panel arrive as per the design you approved, nothing swapped quietly.
- Installation: Our team fits and wires everything. In live sites we plan the noisy work around your working hours.
- Testing: Before we call it done, we test detection, alarms, the release circuit and pressures, and show you the results.
- Handover: We walk your staff through the alarms, the abort and manual release, and what to do if the system ever goes off.
- AMC: After that, regular visits keep it ready. A system that is never checked is a system you are hoping works.
What we check on AMC visits
- Pump start tests (jockey, electric, diesel)
- Alarm valve and flow switch tests
- Pressure gauge readings
- Sprinkler head inspection (paint, damage, obstruction)
- Inspector test valve drain
- Pipe and hanger inspection
- Service report and log book update
The diesel pump is the part that most often lets people down: a flat battery, old fuel or a pump nobody has started in months. Our visits always include a pump run. Frequency is set in your AMC.
You may also need
- Fire Hydrant System Installation
- Fire Alarm System Installation
- Fire Safety Audit
- Automatic Modular Fire Extinguisher
- Guide: Fire NOC process in Delhi NCR
Planning a new building or fixing an old system? Call or WhatsApp +91 85870 53556, or send an enquiry with your drawings if you have them.
Design, testing & support
Fire sprinkler systems for warehouses, factories, malls, hotels and offices across Delhi NCR: design, installation, testing and AMC.
Site-specific design
Each system is sized for the room, panel, kitchen, building or vehicle it protects.
Tested at handover
Every installation is tested and commissioned before handover.
- Free site survey across Delhi NCR.
- System chosen for your actual fire risk.
- Protects equipment, people and operations.
- Reduces downtime and repair costs.
- Professional installation, testing and commissioning.
- Regular inspection, maintenance and AMC services.
Everything you need to know about Sprinkler System Installation in Delhi NCR
Each head has a glass bulb that breaks at a set temperature. Only the heads heated by the fire open and spray water, the rest stay closed.
No. In wet, dry and pre-action systems only the heads near the fire open. Only a deluge system opens all its heads at once, and it is used for special risks.
The pipes stay dry until a detector confirms a fire, then fill with water. It is used where an accidental leak would be costly, such as archives.
Usually a jockey pump to hold pressure, a main electric pump and a diesel standby pump, sized for the building and its risk.
Ye building ke size aur pipe network par depend karta hai. Site visit aur design ke baad hum poora timeline bata dete hain.
Yes. We test pumps, valves and heads, fix faults and take systems under AMC.